曾道长资料大全2020

板式换热器厂家德律风

4000488890

曾道长资料大全2020

讨论曾道长资料大全2020

工厂地址:天津经济技术开拓区洞庭二街7号
贩卖公司地址:天津市河西区洞庭路16号美年广场3号楼322
贩卖热线:022-26998183
贩卖热线:13389980785
德律风:4000488890
德律风:4000488890
传真:022-26996185
邮编:300409
邮箱:tpy_phe@sina.com
诚征天下各地代理商:讨论德律风022-26998183

曾道长资料大全2020

以后位置:主页 > 曾道长资料大全2020 >

怎样去提高板式换热器传热的技术

作者:搜索引擎优化源头:未知2019-12-27 11:44
择要:板式换热器 得怎样去提高传热技术呢?着实只需同时去提高板式冷热两侧的外貌的传热系数的,并且得淘汰污垢层面,选择热传导率高的版片,再次就是得淘汰板片的厚度啦,多么才可

      板式换热器得怎样去提高传热技术呢?着实只需同时去提高板式冷热两侧的外貌的传热系数的,并且得淘汰污垢层面,选择热传导率高的版片,再次就是得淘汰板片的厚度啦,多么才可以有效的提高板式换热器的传热系数的。
 
  一、提高板片的外貌传热系数由于板式板式换热器的波纹能使流体在较小的流速下孕育发生湍流 (雷诺数一 150时 ),因此能失失较高的外貌传热系数,外貌传热系数与板片波纹的多少布局以及介质的活动外形有关。板片的波形包括人字形、平直形、球形等。颠末多年的研讨和实行发现,波纹断面外形为三角形 (正弦形外貌传热系数很大,压力降较小,受压时应力散布匀称,但加工困难? )的人字形板片具有较高的外貌传热系数,且波纹的夹角越大,板间流道内介质流速越高,外貌传热系数越大。
 
  二、减小污垢层热阻减小板式换热器的污垢层热阻的关键是防范板片结垢。板片结垢厚度为 1 mm时,传热系数飞扬约 10%.因此,必需过细监测板式换热器冷热两侧的水质,防范板片结垢,并防范水中杂物附着在板片上。有些供热单位为防范盗水及钢件蜕化,在供热介质中添加药剂,因此必需过细水质和黏 剂惹起杂物沾污板式换热器板片。要是水中有黏性杂物,应采取公用过滤器举行处置处分。选用药剂时,宜选择无黏性的药剂。
 
  三、选用热导率高的板片板片材质可选择奥氏体不锈钢、钛合金、铜合金等。不锈钢的导热遵从好,热导率约 14. 4 W/(m.K) ,强度高,冲压倒从好,不易被氧化,价钱比钛合金和铜合金低,供热工程中运用很多,但其耐氯离子蜕化的技艺差。

         How to improve the heat transfer technology of plate heat exchanger? In fact, as long as the heat transfer coefficient of the surface on both sides of the plate is improved at the same time, and the dirt layer is reduced, and the plate with high heat conductivity is selected, the thickness of the plate is reduced again, so that the heat transfer coefficient of plate heat exchanger can be effectively improved.

  1、 To improve the surface heat transfer coefficient of plate plate heat exchanger, because the ripple of plate heat exchanger can make the fluid produce turbulence at a small flow rate (Reynolds number 150), so it can obtain a higher surface heat transfer coefficient. The surface heat transfer coefficient is related to the geometry structure of plate ripple and the flow state of medium. The waveforms of the plates include herringbone, straight, spherical, etc. After years of research and experiments, it is found that the herringbone plate with triangular corrugated cross-section (sinusoidal surface heat transfer coefficient is large, pressure drop is small, stress distribution is uniform under pressure, but it is difficult to process?) has a high surface heat transfer coefficient, and the larger the included angle of corrugations, the higher the flow velocity of medium in the channel between plates, the greater the surface heat transfer coefficient.

  2、 The key to reduce the thermal resistance of the fouling layer of the plate heat exchanger is to prevent the fouling of the plate. When the scale thickness of the plate is 1mm, the heat transfer coefficient will be reduced by about 10%. Therefore, it is necessary to monitor the water quality on both sides of the plate heat exchanger to prevent the scaling of the plate and prevent the water impurities from adhering to the plate. In order to prevent water theft and steel corrosion, some heating units add chemicals to the heating medium. Therefore, it is necessary to pay attention to the contamination of plate heat exchanger caused by water quality and viscosity. If there are sticky impurities in the water, special filter shall be used for treatment. When choosing the medicament, it is better to choose the medicament without viscosity.

  3、 Austenitic stainless steel, titanium alloy, copper alloy, etc. can be selected for the plate with high thermal conductivity. Stainless steel has good thermal conductivity, thermal conductivity is about 14.4w / (m.k), high strength, good stamping performance, and is not easy to be oxidized. Its price is lower than that of titanium alloy and copper alloy. It is widely used in heating engineering, but its ability to resist chloride ion corrosion is poor.